AnnoManager class resource descriptions

amOn
This boolean resource specifies whether the base plot should draw the annotation View object along with the other objects comprising the plot.

Default: True

amViewId
You can use this resource to retrieve the id of the View object controlled by the AnnoManager. Note that this resource can be set only when the AnnoManager object is created.

Default: <dynamic>

amResizeNotify
If this boolean resource is True, the PlotManager sets the height and width of the annotation item whenever the size of the base plot's viewport changes. Height is adjusted based on the ratio of the new viewport height to the old height. Width is adjusted based on the ratio of the new viewport width to the old width.

Default: False

amTrackData
When amTrackData is set False, the PlotManager locates the annotation View object in NDC space using the PlotManager Location Control Model resources amZone, amSide, amParallelPosF, amOthogonalPosF and amJust. If amTrackData is True, the annotation is positioned relative to the data coordinate space of the base plot. In this case, the PlotManager determines the base position of the annotation item from the values of the resources amDataXF and amDataYF. The resources amZone, amSide, amParallelPosF, and amOthogonalPosF are ignored. However, the resource amJust still determines the justification point of the annotation with respect to its base location.

Default: False

amZone
If amTrackData is False, amZone specifies the PlotManager zone assigned to the annotation. amZone is one of the resources you must set in order to control the location of the annotation in a manner consistent with the rules of the PlotManager Location Control Model. If amZone is set to 0, the annotation is located relative to the center of the PlotManager viewport; otherwise, it is located relative to one side of the zone's interior boundary, which is the bounding box of the previous zone.

Default: 0

amSide
If amTrackData is False, this resource of type NhlTPosition determines which of the zone's interior sides to use as a base for establishing the coordinate system within which the annotation is placed. The PlotManager Location Control Model requires this resource to allow control of the annotation in a manner consistent with other annotations. Its value determines the origin of the coordinate system and the direction of the positional resources, amParallelPosF and amOrthogonalPosF. It also constrains the value of amJust appropriately. There are four settings, which behave as follows, unless amZone is set to one of the special zones (0 or 1):
NhlTOP
The PlotManager locates the annotation relative to a line paralleling the top viewport boundary. amOrthogonalPosF increases in the direction of increasing NDC Y-Axis values and is constrained to positive values. amParallelPosF increases in the direction of increasing NDC X-Axis values. amJust is constrained to NhlBOTTOMRIGHT, NhlBOTTOMCENTER, or NhlBOTTOMLEFT.
NhlBOTTOM
The PlotManager locates the annotation relative to a line paralleling the bottom viewport boundary. amOrthogonalPosF increases in the direction of decreasing NDC Y-Axis values and is constrained to positive values. amParallelPosF increases in the direction of increasing NDC X-Axis values. amJust is constrained to NhlTOPRIGHT, NhlTOPCENTER, or NhlTOPLEFT.
NhlRIGHT
The PlotManager locates the annotation relative to a line paralleling the right viewport boundary. amOrthogonalPosF increases in the direction of increasing NDC X-Axis values and is constrained to positive values. amParallelPosF increases in the direction of increasing NDC Y-Axis values. amJust is constrained to NhlTOPLEFT, NhlCENTERLEFT, or NhlBOTTOMLEFT.
NhlLEFT
The PlotManager locates the annotation item relative to a line paralleling the left viewport boundary. amOrthogonalPosF increases in the direction of decreasing NDC X-Axis values and is constrained to positive values. amParallelPosF increases in the direction of increasing NDC Y-Axis values. amJust is constrained to NhlTOPRIGHT, NhlCENTERRIGHT, or NhlBOTTOMRIGHT.
If amZone is set to 0, the PlotManager locates the annotation item relative to the viewport center. If amZone is 1, the annotation is located relative to the viewport boundary itself, and the direction of the amOrthogonalPosF is opposite to the specification given above. Also if the amZone is either 0 or 1, amJust is not constrained, and amOrthogonalPosF may take on negative values.

Default: Bottom

amParallelPosF
If amTrackData is False, amParallelPosF specifies the coordinate of the base location of the annotation parallel to the current amSide and directed toward increasing NDC values. The PlotManager Location Control Model requires this resource to allow control of the annotation in a manner consistent with other annotations.

Default: 0.0

amOrthogonalPosF
If amTrackData is False and amZone is not equal to one, amOrthogonalPosF sets the coordinate of the base location of the annotation orthogonal to the current amSide and directed away from the center of the PlotManager viewport. If amZone is equal to one, the direction is from the viewport side specified by amSide toward the viewport center. The PlotManager Location Control Model requires this resource to allow control of the annotation in a manner consistent with other annotations.

Default: 0.0

amJust
This resource of type NhlTJustification, after constraint to an appropriate value based on amSide, sets the justification point of the annotation with respect to its base location. The PlotManager Location Control Model requires this resource to allow control of the annotation in a manner consistent with other annotations. Note that amJust still has an effect when amTrackData is True. Normally, amJust is constrained based on the value of amSide. However, if amZone is 0 or 1, or amTrackData is True, the PlotManager does not constrain amJust.

Note in addition that the position of the justification point is determined from the viewport of the annotation View object only. That is to say, while it is possible that View object's bounding box might be larger than its viewport, any extent outside the viewport is not considered when determining the justification point. This means that that there is the possibility of overlap if a View object has elements extending outside its own viewport along the edge closest to the PlotManager Plot viewport.

Default: CenterCenter

amDataXF
When amTrackData is True, amDataXF sets the X coordinate of the annotation item's base location.

Default: 0.0

amDataYF
When amTrackData is True, amDataYF sets the Y coordinate of the annotation item's base location.

Default: 0.0


Reference Manual Control Panel

NG4.1 Home, Index, Examples, Glossary, Feedback, Ref Contents, Ref WhereAmI?


$Revision: 1.11 $ $Date: 1999/04/09 17:22:15 $